Menu
EUR

Insulate your boot against road and exhaust noise

Insulate your boot? Reduce road noise, tyre noise and resonance with sound-damping mats and a sound-insulating boot mat.

Soundproofing the boot against road noise and exhaust noise

Want less road noise, tyre noise and resonance in your car? Then soundproofing the boot is a smart first step. The boot floor sits close to the road surface, the wheel arches and often also the exhaust line. As a result the boot panel can start to vibrate and pass sound on to the cabin, especially to the rear seats.

With the right boot insulation you reduce these vibrations at the source. You apply the vibration isolation to the bare sheet metal on the inside of the car. So nothing needs to be fitted to the outside of the vehicle.

Why is the boot an important place to insulate?

The boot floor sits just above the rear part of the chassis. Vibrations from the tyres, wheel arches, exhaust and suspension can be amplified via the thin sheet metal. That sheet metal then acts as a soundboard, so sound reaches the interior more easily.

Because the boot is often less extensively insulated from the factory than the cabin, this is a place where you can achieve a noticeable result relatively easily. Especially in hatchbacks, estate cars, vans and cars with an open connection between boot and rear seats, boot insulation can make a big difference.

Which materials do you use for boot insulation?

To insulate the boot you usually use two layers. The first layer is a self-adhesive vibration damping mat applied directly to the bare sheet metal. This mat adds mass and damps vibrations of the metal. As a result the boot panel is less likely to resonate.

For extra comfort and a neat finish you can place a sound-insulating boot mat on top. This finishing layer helps with further damping, protects the load floor and keeps the boot looking well cared for. Alternatives for the finish are, for example, needle felt with granulate backing or a suitable cargo floor mat.

Benefits of soundproofing the boot

  • Less resonance of the sheet metal in the boot.
  • Noticeably less road noise and tyre noise in the interior.
  • Also suitable for reducing noise at the rear seats.
  • Easy to do yourself with self-adhesive damping mats.
  • Can be finished neatly with a sound-insulating boot mat.
  • Combines well with insulation of the floor pan and spare wheel well.

Step-by-step guide: soundproofing a car boot

Soundproofing a car boot is easy to do yourself if you work carefully and prepare the sheet metal well. Be sure to take your time cleaning, fitting and pressing down the mats. Good adhesion largely determines the end result.

  1. Remove the lining from the boot floor and any side panels, so that the bare sheet metal is visible.
  2. Check the boot for moisture, rust or dirt. Fix this first before you apply insulation material.
  3. Clean and degrease the surface thoroughly with a suitable cleaner.
  4. Measure the boot floor, wheel arch sections and any spare wheel well.
  5. Cut the damping mat to size with scissors or a craft knife.
  6. Warm the mat lightly with a hairdryer if the material needs to become more pliable.
  7. Remove the protective film and stick the mat firmly onto the sheet metal.
  8. Press the mat down well everywhere with a roller, especially in corners, around ribs and on uneven parts.
  9. Cover as much of the available sheet metal as possible, including the spare wheel well if there is one.
  10. Then, if desired, put back a sound-insulating boot mat or other finishing layer.

How much sheet metal should you cover?

For a good result it is wise to cover as much of the available sheet metal in the boot as possible. The boot floor is often not completely flat because of ribs, wheel arch raised sections or a spare wheel well. It is precisely these shapes that can transmit vibration, so pressing down carefully is important.

You do not need to cover every plastic panel. Focus mainly on metal parts that directly transmit sound and vibration. Think of the boot floor, the sides, the wheel arch sections and the spare wheel well.

Combine the boot with the floor pan and spare wheel well

The boot is often connected to the floor pan of the cabin. That is why boot insulation works best when you also include the adjacent parts. Preferably insulate the spare wheel well, wheel arches and, if desired, the floor pan under the rear seat in the same way.

Mainly want less noise at the rear seats? Then the combination of boot floor, wheel arches and spare wheel well is usually more logical than a single loose mat on the load floor.

Soundproofing the boot with materials from Geluidsisolatie Deal

At Geluidsisolatie Deal you will find self-adhesive damping mats and sound-insulating floor mats that are suitable for soundproofing the boot, floor pan, wheel arches and spare wheel well. This lets you reduce the vibrations of the sheet metal and finish the boot neatly.

Not sure how much material you need or which combination suits your car best? Get in touch with us. We are happy to help you think it through based on the type of vehicle, the shape of the boot and the noise you want to reduce.

Frequently asked questions about soundproofing the boot

Why is the boot an important place to insulate?

 

The boot floor is close to the road surface, the wheel arches and often the exhaust. As a result, vibration and sound can be passed on to the interior via the sheet metal.

Can I soundproof my car's boot myself?

 

Yes, this is easy to do yourself with self-adhesive damping mats, a craft knife or scissors and a roller. Do make sure the sheet metal is clean, dry and degreased before you start.

Do I have to cover the entire boot panel?

 

For the best result you cover as much sheet metal as possible. Focus mainly on the boot floor, wheel arches, sides and spare wheel well. You usually do not need to cover plastic panels.

What is the difference between a damping mat and a boot mat?

 

A damping mat is stuck directly onto the sheet metal to reduce vibration. A boot mat is usually used on top of that as an extra sound-insulating and protective finish.

Does boot insulation also help against exhaust noise?

 

Boot insulation can reduce exhaust noise in the interior, especially when sound is transmitted via the floor or spare wheel well. The result depends on the car, the exhaust and the amount of insulated sheet metal.

Choose your language
Choose your currency
€

Recently added

Total incl. tax
0,00
Order for another €75,00 and receive free shipping
0
Compare
Start comparison

This product has been added to your cart